Jump to content

Jake Middleton-Metcalfe

  • Posts

  • Joined

  • Last visited

Everything posted by Jake Middleton-Metcalfe

  1. you can always send it to C.Wheatstone and Co they are still trading. It might be best to do that rather than have new buttons posted to you - the buttons in your in your instrument might be different from the new ones they would have in some way and as a consequence the action might also need adjusting - which also then entails re tuning. The best thing to do would be to send it to a company that can re make/replace the buttons and then adjust the instrument all in one go, maybe there is someone in America who could to this rather than you having to send it to the UK - you could always investigate, but of course Wheatstone is still there. Best wishes Jake
  2. That all makes perfect sense, im imagining sounding the reeds while they are mounted in the reed blocks by holding the block over a tuning jig with an air hole that the reed block is placed over to activate each individual reed to detect the pitch it sounds while outside the instrument? I think Morse concertinas must have had a slightly different setup for tuning in their workshop as the action and reedpan were one glued together part and then the reeds were waxed on. Perhaps they had a tuning bellows which was set up in a different way and the whole action assembly could be attached and easily removed.
  3. Beware of one thing, if you wanted to put some different/better reeds in: I have made a number of instruments using voici armoniche tam reeds and once asked them if their a Mano sets were the same size as their tam and was told they are not, there may also be a difference between dural and tam but I have no idea. I used to order about 20 sets at a time from this company and it was a very very slow process. The reeds are good though to be fair to the company. Maybe the thing to do might be to try and obtain the sizes of the reed plates from the manufacturer and if it's going to fit your instrument then order a single set through carini if they are stocking them. There will be quite some fine tuning to do on the new reeds as well so you will need a decent tuning set up. I'm not sure how Morse concertinas did that as I know their reeds are waxed in, maybe with reed scratchers? I am not sure. Best of luck with the project if you decide to go ahead, it's not that easy a task
  4. Probably the best thing is to have one made for you at C.Wheatstone and Co - they are only in Stowmarket, a short drive from Ipswich. The cases made there are excellent, they are hard cases though. I would really caution anyone to not use soft cases for concertinas, its just asking for trouble, ask any concertina maker how many bashed in or bent in ends they have had to repair due to soft cases. http://www.wheatstone.co.uk/
  5. very very thick metal! Are the sides of the action box in that metal as well? It sort of looks as if they are.
  6. Is his son Bob ham, who lives in Moulton?
  7. Aha. With metal ends sometimes the problem relates to electroplating which is partially worn. The ends being either brass or nickel silver with usually a nickel plating to prevent tarnishing. After a lifetime of playing some wear is inevitable. There are a couple of ways to solve it you can have it stripped in an acid which attacks nickel which is probably ok for brass but risky on nickel silver or you can polish it and get it copper plated then nickel plated over the flawed original plating. I have had done the copper approach twice, once it went well and once it went badly. The main problem is concertina makers don't usually have their own electroplating equipment and you end up having to give the parts to someone else. That is where everything is very likely to go wrong. Thus in the end usually during repair the ends just get a not too aggressive polish as it's less risky.
  8. I believe Andrew Norman makes 40 button Anglo concertinas with accordion reeds, the instruments are 7" across the flats, his work is well made and the instruments play well. You can read about his work here: http://www.acnorman.co.uk/ Andrew has explored the possibilities of making concertinas with accordion reeds rather a lot from what I can see, probably more than anyone.
  9. Interesting design, can I ask: Is that instrument a bit bigger than 6 and 1/4"? Looks a bit bigger (not a bad thing for a 40b in my opinion) Im just curious as I lately played a 40b Wheatstone that was 6 and 1/2" - the extra space was used to put in longer scale reeds, it played really, really well. As in, honestly I think it was the best old concertina I have played.
  10. well done, its sometimes a bit overlooked, the need for a robust case that holds the instrument securely in the closed position. It looks great too.
  11. thanks for sharing the images. I haven't worked on any Jeffries duets actually, quite interesting.
  12. I have personally not had to deal with this issue ever, all of the 38 key Jeffries instruments I ever worked on had the inboard reed frames screwed down, does anyone have any pictures of this different not easily removable setup? Sounds like one to be wary of. Also Clive I did after a few years actually make a "reed pulling tool" to make taking reeds out for tuning - someone told me Geoff Crabb had one and I thought "well that sounds quite useful actually", easier on the finger tips!
  13. That is pretty interesting. I would say 5-6 weeks to make an Edeophone is very fast really, given the complexity of those instruments and how many hand made reeds they have. Its hard to say how many man hours that would be though - I would guess that the instrument would have been worked on by more than one person at once, making different parts. From what I have learned Lachenal and Wheatstone practiced very good division of labour and ran a rather efficient production line.
  14. I think you are quite correct in saying that the 20b was very rarely or almost never made to a top standard. No one ever particularly said this to me but I haven't seen a 20b that was made to the full extent of the makers abilities, I am talking about historic makers here. There is nothing to say someone could not approach a professional maker today and ask for a very well made 20b but it would be an unusual request as it would probably cost almost as much as asking someone to make a 30b. A bit less of course but probably not 1/3rd less as might be implied by the number of buttons. In for a penny, in for a pound as they say.
  15. Thanks for sharing the diagram that is always interesting to see. I have saved that one for future reference FYI: the layouts for 38 key jeffries layouts on my website came from Geoff Crabb and I believe to be the closest thing to a "standard".
  16. That is pretty unusual. If the reeds are stamped with the same notes as they are sounding then as far as we know that is original. Its likely someone would ask for something like that, no one has ever asked me to make a 38 button instrument that was the same as any other 38 key I made, such idiosyncrasies must have existed in the past too I would guess. Jeffries and Wheatstone had slightly different ideas about where to put the extra buttons though with Wheatstone tending to add them at the end of each row and Jeffries tending to add them to the end of two of the rows and then putting one down below the usual three rows - I am guessing the accidental row is usual Wheatstone accidentals and the extra buttons are something approximating Wheatstone but not necessarily in the same place? I hope it is good fun to play! Best wishes Jake
  17. Gosh that is a tough situation. In the UK concertina production only just survived the 2nd world war, but a couple of small businesses managed to continue.. It sounds like a sort of similar situation but a bit harder for you guys in Argentina if the production completely stopped in WW2. It can be hard to revive an industry or industrial processes but not impossible.
  18. Sorry to hear no one in the bandoneon world is being very helpful to you. Is the bandoneon industry rather secretive? I would also recommend C1095 in hardness condition rockwell 48-51. Then you need lots of files. Some sort of shearing tool is needed to get it into strips, that is a tricky part you might have to improvise your own as the usual lever type mounted to a bench is not suitable, other commercially available options might work.. Other simpler ways of cutting it into strips include scoring a line on the steel, clamping it in a vice and then hitting the bit hanging out of the vice very hard with a big piece of metal. (that process involves the least investment of tools anyway) Best of luck with your project, its a hard thing to do but with good dedication all things are possible.
  19. As can be taken from the above replies - making reeds is very involved. Its really going to be very hard or almost impossible if you don't at least have a set of reeds which you like that you could try to copy. What I did is study historical reeds which I liked before taking steps to learn from experienced reed makers and begin to do a lot of experiments. I would recommend buying some reeds if there is anything available which would be usable for your project, making your own reeds is only a choice you take if what you want is not available to buy at all, which is what many concertina makers have to do. Hopefully you can find something you can buy which will work for your needs. Probably a helpful way to think of it is "free reed instrument making is a discipline and reed making is another discipline which you would only learn if you felt you have to" But if making reeds is really in your heart and you feel you really want to do it ... Do it. Enthusiasm for a topic of experimentation is a good thing.
  20. Hello Clive Its quite a tricky thing for makers. Basically the nickel silver you can get nowadays is of quite a different composition to what was available in the past. The only stuff I could find in the correct thickness and hardness was 12% nickel content. You can get 18% nickel silver but I have never found anywhere which will supply it to the correct thickness of sheet. The long and short of it is that the higher the nickel content the less it tarnishes, really you want something with about 30% Nickel, the rest being mostly copper and a bit of zinc, I think that is what Jeffries used, or something similar to that. You cant really get it now so you have to electroplate really. The proper modern equivalent would probably be "cupro nickel" which is 30% nickel and 70% copper - its what a British 50p is made of. Again you cant find this in the right thickness for concertina ends which is normally anything from 0.71mm thick to 0.91 thick depending on the design. If anyone ever found some of that I would want to know about it! See you at a session some day I hope, you are only one country over from me in Northamptonshire.
  21. Best thing is to get in touch with the maker, the problem might actually be caused by your skin, some peoples skin seems to have more of an effect on nickel than others. I have always found that nickel silver in its modern form needs bright nickel plating to stay looking good. Or you can go for chrome but that doesen't always look as good and the process is a bit more fraught with error - the upside with chrome being that it is supposedly very durable though. Best talk to the maker and ask what he recommends, and probably any modification best employ him to do it rather than a third party.
  22. Steve Dickinson (C.Wheatstone and co) still makes them to original patterns you could ask him to make you one.
  23. I didn't think about that. The subtle difficulties of the multi instrumentalist I suppose.
  24. I suppose thing thing is you would have to remember to trim your finger nails regularly, I remember playing an instrument where the buttons stop flush with the end and I had not, the thing is then is that your finger nails touch the end before the button is all the way down resulting in a bit of an un ... "definite" end to the button stroke and possibly the pad doesn't lift all the way in such a case if you haven't pushed the button all the way down in such a case. Trimming nails is generally a good thing to do regularly anyway though.😆 The especial thing to beware of with not pressing the button down all the way is that the amount to which the pad lifts affects the tuning, the note sounds at a slightly different pitch. One of the main reasons concertinas go "out of tune" is actually because the pads have compressed or sunken down over years and the overall lift is greater which affects the tuning a little. Not really a problem if you have trimmed your nails though.
  • Create New...