Theo Posted November 9, 2021 Share Posted November 9, 2021 5 hours ago, Fanie said: Thank you Theo. I am going to try to make one from the shaft of an old drill bit, but how do you drill into hard steel? I don't know. I used tool steel as supplied which is not to hard to drill. If your old drill shaft is carbon steel you can soften it by heating to red and cooling slowly. If it's high speed steel I don't know. Link to comment Share on other sites More sharing options...
Fanie Posted February 5, 2022 Author Share Posted February 5, 2022 (edited) Time for an update: I made a new set of 8-fold bellows I made a set of new deldrin/acetal buttons I made new pads and I made new springs from 0.7mm stainless steel spring wire. Now for my big headache, the reeds. The reeds sound terrible. Some of them don't make a sound and the rest are out of tune. Some of them were so rusted and pitted that I do't know if it will be possible to tune them. Now I have been thinking............ I have an old Scandalli piano accordion that is beyond repair, but the reeds are still looking good. It has about 120 treble reeds. If I could harvest a set of reeds from the PA and then cut half of the reed plate off so that it is a single tongue reed and then file the reed plate to shape and then drill holes on both ends to attach it with screws? What do you think? Edited February 5, 2022 by Fanie Link to comment Share on other sites More sharing options...
Fanie Posted February 10, 2022 Author Share Posted February 10, 2022 (edited) It is time time to start doing something about the reeds in my Wheatstone. I cleaned all the rust out and started testing the pitch. I have two tuner apps on my phone, which are Pano Tuner, and I have Billthefarmer Tuner. Both apps measure the pitch in Hz an my reeds are way out of pitch. I first tested the right hand side reeds and made a tabel of what it should be (Target Hz), and what it is currently testing (Current Hz). Right hand reeds: Reed Target Hz Current Hz C#5 554.73 546 D#5 662.25 604 A5 880 857 G5 783.99 747 G#5 830.61 800 Bb5 932.33 903 C#6 1108.73 1095 D#6 1244.51 1173 A6 1760 1587 F6 1396.91 1246 E6 1318.51 1182 B5 987.77 963 B6 1975.53 1780 F#6 1479.98 1425 C6 1046.50 962 A5 880 845 G6 1567.98 1482 E6 1318.51 1256 D6 1174.66 1092 C6 1046.50 1011 G5 783.99 760 F5 698.46 B5 987.77 949 A5 880 868 E5 659.25 620 D5 587.33 583 G5 783.99 750 F#5 739.99 728 C5 523.25 490 B4 493.88 481 As you can see, they are WAY out of tune. Please tell me if it will be possible to tune these reeds to what they should be. Thank you for you help. Edited February 10, 2022 by Fanie Link to comment Share on other sites More sharing options...
Rod Pearce Posted February 10, 2022 Share Posted February 10, 2022 Double check your Target values. You have D#5 as 662.25 but I believe it is 622.25! See this table of note values. You can use it to work out what your current reeds are set to. Better still your tuner app may tell you https://en.wikipedia.org/wiki/Piano_key_frequencies Providing the reeds have not be tuned too much you should be able to retune by half a tone up or down relatively easily. Link to comment Share on other sites More sharing options...
Rod Pearce Posted February 10, 2022 Share Posted February 10, 2022 A simpler table, Equal Temperament https://pages.mtu.edu/~suits/notefreqs.html Link to comment Share on other sites More sharing options...
alex_holden Posted February 10, 2022 Share Posted February 10, 2022 If you're using a tuning app, you normally don't need to worry directly about frequencies, other than when you set your pitch reference (e.g. A4=440Hz). The app autodetects what note you are playing, then calculates how far off it is from what it should be and expresses the result in cents. A cent is a hundredth of a semitone. You need to have an idea of what note you expect the reed to play, because if it is more than 50 cents off the tuner may show you the wrong note (e.g. it may say F# -45c when it's actually F +55c). The app I use is called TonalEnergy Tuner & Metronome. Link to comment Share on other sites More sharing options...
Fanie Posted February 11, 2022 Author Share Posted February 11, 2022 So are you not using the frequencies to tune the reeds? Link to comment Share on other sites More sharing options...
alex_holden Posted February 11, 2022 Share Posted February 11, 2022 15 minutes ago, Fanie said: So are you not using the frequencies to tune the reeds? No, apart from initially setting the reference pitch I only pay attention to the cents error number. Link to comment Share on other sites More sharing options...
Rod Pearce Posted February 11, 2022 Share Posted February 11, 2022 (edited) I have just had a brief look at the Pano Tuner website, and the display only seems to show the note value and frequency (eg A and 440.0 hz). Other tuners also show how many cents the note being sounded is above or below the required pitch I believe this is what Alex is referring to, and it seems cents is not available on that tuner. Bill the farmer tuner does appear to show cents, so I suggest you use that one if you are familiar with it. When you sound the note it will show you what note it is nearest to and how many cents above or below that note it is. You are looking to get it to as near as 0 cents as possible, So Sound the reed Look at what the tuner says the note is and how far above/below pitch it is in cents. Tune the reed up or down and re-sound until you get as near as you can to 0 cents. Does this make sense? Edited February 11, 2022 by Rod Pearce Link to comment Share on other sites More sharing options...
alex_holden Posted February 11, 2022 Share Posted February 11, 2022 6 minutes ago, Rod Pearce said: I have just had a brief look at the Pano Tuner website, and the display only seems to show the note value and frequency (eg A and 440.0 hz). Other tuners also show how many cents the note being sounded is above or below the required pitch In the screenshot of Pano Tuner, I would guess the gauge directly above the note display (with green bars from +10 to -10) is showing the cents error. Link to comment Share on other sites More sharing options...
Rod Pearce Posted February 11, 2022 Share Posted February 11, 2022 Yes Alex, I think you are right. Never noticed it before Link to comment Share on other sites More sharing options...
Richard Mellish Posted February 12, 2022 Share Posted February 12, 2022 19 hours ago, alex_holden said: In the screenshot of Pano Tuner, I would guess the gauge directly above the note display (with green bars from +10 to -10) is showing the cents error. If so it's confusing, because 10 seems to correspond to half a semitone. Link to comment Share on other sites More sharing options...
alex_holden Posted February 12, 2022 Share Posted February 12, 2022 3 minutes ago, Richard Mellish said: If so it's confusing, because 10 seems to correspond to half a semitone. Yes, the designer of that app obviously favoured its artistic design over usability and features. Bill the Farmer's tuner is unusual in that it seems to be primarily intended for tuning instruments that have pairs of reeds, e.g. melodeons and accordions. Link to comment Share on other sites More sharing options...
Fanie Posted February 13, 2022 Author Share Posted February 13, 2022 (edited) Thank you for the help gentlemen, I appreciate it. So if the error measurement is "+" cents off, you file the tip of the reed, and when it is "-" off, you file the base of the reed? How much maximum error is it possible to change? Thanks Edited February 13, 2022 by Fanie Link to comment Share on other sites More sharing options...
alex_holden Posted February 13, 2022 Share Posted February 13, 2022 2 hours ago, Fanie said: Thank you for the help gentlemen, I appreciate it. So if the error measurement is "+" cents off, you file the tip of the reed, and when it is "-" off, you file the base of the reed? How much maximum error is it possible to change? Thanks No, that's backwards. A + error means it's sharp, so you need to flatten it by either weakening the read near the clamp or adding extra weight to the tip. A - error means it's flat so you need to sharpen it by removing weight from the tip. It's impossible to say how much of an adjustment you can get away with because it depends on how thin they are already. Removing metal makes the reeds weaker which may limit their performance (unless they were manufactured too heavy to start with). If they have been heavily tuned in the past there might not be a lot of material left to remove. With very high reeds in particular they can become so thin at the tip that the metal just disintegrates. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now