Michael Eskin Posted October 3, 2017 Share Posted October 3, 2017 A friend of mine recently took delivery of a phenomenal Jeffries 30-button which had some serious restoration work done by Dipper. The spring tension on all the buttons across the board is quite high, which she's adapting to, but the air button has about twice the spring tension of the other buttons on the instrument and I think is way too high. The air button actually painful to use for any length of time and she's getting tendonitis in her thumb from activating it. Looking at the design of the air button, it appears to have a single-wire, double sprung mechanism unlike the other buttons on the instrument. It appears to be a single-piece V-shaped saddle spring with two coil springs on either side of the lever. This is way beyond my ability to adjust, any suggestions who might be able to do the work for her to lighten the air button spring tension without having to ship the instrument all the way back to England? She's in San Diego, CA. Thanks for any suggestions, Michael Link to comment Share on other sites More sharing options...
Chris Ghent Posted October 3, 2017 Share Posted October 3, 2017 Picture..? Link to comment Share on other sites More sharing options...
Michael Eskin Posted October 3, 2017 Author Share Posted October 3, 2017 I don't have one available, sorry. Link to comment Share on other sites More sharing options...
alex_holden Posted October 3, 2017 Share Posted October 3, 2017 Could you perhaps replace it with a pair of standard springs? Link to comment Share on other sites More sharing options...
adrian brown Posted October 3, 2017 Share Posted October 3, 2017 Could you perhaps replace it with a pair of standard springs? ... or even a single one? Unless she's a player who likes to give it a lot of welly, a single spring might well be enough. Adrian Link to comment Share on other sites More sharing options...
Dana Johnson Posted October 3, 2017 Share Posted October 3, 2017 Im sure Greg Jowaisas could deal with this in a few minutes. I dont know any west coast repairers, though there may be some. There is theoretically nothing wrong with that kind of spring which just more tidily duplicates using two springs. But either the wire gage is too large, or there are two few coils. You could try taking off some of the preload by removing the spring, putting any sort of mandrel through the coils and wrap the legs just enough more so they spring back a few degrees less. It is easy to open them up if you over do it. Torsion springs like these build tension slowly, so removing say half the preload, ( the amount it must be compressed before it hooks into place ) it will be relatively constant at the new pressure. You only need enough pressure to keep the pad down against the air pressure. Sometimes people spring too heavily to counter a misaligned or tilted pad, or one with a leaky surface rather than addressing the underlying issue. Dana Link to comment Share on other sites More sharing options...
d.elliott Posted October 3, 2017 Share Posted October 3, 2017 Saddle Spring???? or are you talking about two 'standard' type springs but from a continuous length of wire? one each side of the lever arm but joined under the lever? Dave Link to comment Share on other sites More sharing options...
John Dipper Posted October 3, 2017 Share Posted October 3, 2017 We are confused, as we don't set up instruments with a 'heavy' action. The brass springs we use in Jeffries concertinas are actually lighter than the originals. As always, we would ask you to contact us if there is an issue - maybe your friend could contact us directly, with a photo of the springs in question and we will be only too happy to help in any way we can. (If they are old springs, then it is best not to adjust them, but if they are new springs, we can instruct you on how to change their pressure). Link to comment Share on other sites More sharing options...
Michael Eskin Posted October 3, 2017 Author Share Posted October 3, 2017 Hi John, I know, that's what is so odd! My friend is aware of this thread and will respond on her own. I can possibly do the work for her if given specific instructions. Cheers, Michael Link to comment Share on other sites More sharing options...
Michael Eskin Posted October 3, 2017 Author Share Posted October 3, 2017 Saddle Spring???? or are you talking about two 'standard' type springs but from a continuous length of wire? one each side of the lever arm but joined under the lever? Dave That's what it looks like. Link to comment Share on other sites More sharing options...
d.elliott Posted October 4, 2017 Share Posted October 4, 2017 I suspect that you have two springs with their contact under the lever extremely close together. you could always try to un-hook one side to see, if oit is two springs leave it un-hooked and see how it feels/ plays. Dave Link to comment Share on other sites More sharing options...
Michael Eskin Posted October 25, 2017 Author Share Posted October 25, 2017 Just to clarify, the spring work wasn't done by Dipper, as was clarified recently to my friend. Absolutely no sleight meant at all on Dipper's work, and if there was any perceived, I apologize profusely. She just wants to get the air button tension lightened and will have someone work on it. Greg, I'm guessing she's already contacted you... Link to comment Share on other sites More sharing options...
Greg Jowaisas Posted October 25, 2017 Share Posted October 25, 2017 The concertina in question is on the bench. It is a lovely Jeffries and of course the work the Dippers did is outstanding. The present owner is a smaller person. I've raised the thumb button for easier access and am addressing the overall spring pressure to make the instrument more friendly to her light, quick Irish Trad approach. Best, Greg Link to comment Share on other sites More sharing options...
Michael Eskin Posted October 25, 2017 Author Share Posted October 25, 2017 Excellent, can't wait to try it out after the adjustments! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now